Dobeck Gen 3 / 3.5 UTV Fuel Programmers
Click To Enlarge

Less shop time means more ride time. The Electronic Jet Kit (EJK) is the #1 EFI controller on the market for installation time to riding with great performance. Plug and play does not just refer to connectors to make installation easy, but the EJK comes programmed and ready to go for stage 1 (after-market pipe and air cleaner) modifications. Forget downloading maps. Forget looking up settings. The EJK installs in mere minutes and you are off to a better, more powerful, smoother ride.

The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the shop that wants to take control of their tuning needs.

GEN 3 is the short term used to describe the Generation 3 Electronic Fuel Injection (EFI) controller manufactured by Dobeck Performance. The GEN 3 was released in 2005 under a private label program. The GEN 3 is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.

The GEN 3.5 EFI controller is an extension to the GEN 3 controller. The GEN 3.5 technology was released in 2009 also in the DP private label program. The GEN 3.5 controller has the ability to add or pull fuel within each available fueling zone.

View Complete Information at



Arctic Cat
Part Number Type Vehicle  
9310210 GEN 3 Arctic Cat Prowler 550/700 2008-2013  
9320109 GEN 3 Arctic Cat Prowler 1000 2009-2013  
8320060 GEN 3.5 Arctic Cat Wildcat 1000i 2012-2015  RECOMMENDED  
9320165 GEN 3 Arctic Cat Wildcat 1000i 2012-2015  
8320127 GEN 3.5 Arctic Cat Wildcat Trail 2014-2015  
Part Number Type Vehicle  
8320018 GEN 3.5 CAN AM Commander 800/1000 2010-2013  
8320062 GEN 3.5 CAN AM Commander 800/1000 2014-2015  
8320062 GEN 3.5 CAN AM Maverick 2013-2015  
CF Moto
Part Number Type Vehicle  
8310076 GEN 3.5 CF Moto 600 UTV 2013  
8320128 GEN 3.5 CF Moto ZForce 800 (Z8) 2015  
Part Number Type Vehicle  
9310195 GEN 3 Honda Big Red MUV 2009-2013  
8310092 GEN 3.5 Honda Pioneer 700 2014-2015  
John Deere
Part Number Type Vehicle  
8320071 GEN 3.5 John Deere Gator 850i 2013  
Part Number Type Vehicle  
9320104 GEN 3 Kawasaki Teryx 2009-2013  
9320213 GEN 3 Kawasaki Teryx 2014-2015  
Part Number Type Vehicle  
8310075 GEN 3.5 Kymco UXV 500i 2013  
Part Number Type Vehicle  
9320105 GEN 3 Polaris Ranger 700XP 2006-2011  
8320056 GEN 3.5 Polaris Ranger 800XP 2011-2014  
9320127 GEN 3 Polaris Ranger 800XP 2011-2014  
9320193 GEN 3 Polaris Ranger 900XP 2013-2015  
8310067 GEN 3.5 Polaris RZR 570 2012-2014  RECOMMENDED  
9310236 GEN 3 Polaris RZR 570 2012-2014  
8320014 GEN 3.5 Polaris RZR/S 800 2008-2010  RECOMMENDED  
9320106 GEN 3 Polaris RZR/S 800 2008-2010  
8320056 GEN 3.5 Polaris RZR/S/4 800 2011-2014  RECOMMENDED  
9320127 GEN 3 Polaris RZR/S/4 800 2011-2014  
8320029 GEN 3.5 Polaris RZR/4 XP900 2011-2014  
8320075 GEN 3.5 Polaris RZR/4/Trail XP900 2015  
8320075 GEN 3.5 Polaris RZR XP1000 2014  
8320114 GEN 3.5 Polaris RZR XP1000 2015  
Part Number Type Vehicle  
9310205 GEN 3 Yamaha Rhino 700 2008-2014  
8310091 GEN 3.5 Yamaha Viking 2014-2015  
Other OEM
Part Number Type Vehicle  
8310070 GEN 3.5 HiSun 550/700 2011-2013  
9340001 GEN 3 Joyner Trooper 1100 2008-2013  
9320134 GEN 3 HiSun 800cc EFI UTV 2011-2013  
9330001 GEN 3 Joyner Sand Viper 800 2008-2013  
9340001 GEN 3 Joyner Sand Viper 1100 2008-2013  
9320117 GEN 3 Redline Riot / Revolt 2010  
9320134 GEN 3 SuperMach UTV 800U 2011-2013  
8310077 GEN 3.5 XY Big Iron 2013  

This EFI controller is one of the only ones on the market which allows a large range of adjustability without the use of a computer. We like to use the term 'on-the-fly' tuning. You can literally drive the vehicle, make setting adjustments, and instantaneously feel the results. Obviously for safety purposes we recommend you pull over to the side before making adjustments. Some after-market EFI controllers like to claim 'on-the-fly' tuning which to them means toggling only between a couple preset maps. The controller actually has 11,390,625 available maps in the unit which are accessible without using a computer program to reprogram the unit. There does exist a computer program called POWERLAB and the controllers can be reprogrammed by a computer, but most users do not require this ability. Why deal with the complexity? It's an Electronic Jet Kit to make fuel injection tuning easy, simple, and fast so you can enjoy more time riding.

    You do not have to be a professional mechanic or tuner and have access to a dynamometer in order to tune your vehicle with the EFI controller. Knowledge and good equipment obviously are a huge plus, but you can do just as good a job and sometimes better by tuning in real world riding situations. The controller allows this by breaking down a drive cycle into very understandable zones to make adjustments. Most controllers have the basic Idle/Cruise, Acceleration, and Full Throttle zones to adjust. Every rider can understand this terminology. The greatest advantage about tuning your vehicle yourself is your ride will be custom set up to your driving style.

  • Plug N' Play Installation - Minutes to Install, Base Settings are Preset
    All of the offered controllers are plug n' play installations and can be done in a manner of minutes instead of hours. All you have to do is locate the OEM injector connections on your vehicle. Most of the time this will only require you to remove a few components to gain access to these injector connections. A number of new applications will also require you to find the O2 connections on your vehicle if present. Power for the unit is gained through the injector connections and a black ground wire just needs to be attached to the negative terminal on the battery if present or by a metal screw onto the vehicle frame. After physically installing the controller in most cases you are all set to go on a test ride. The unit comes pre-programmed for a stage 1 setup for each application. After your initial test ride you then can make some fine tune adjustments which may be required based upon your modifications.

  • Uses Unique Load Based Technology
    The controller uses Load Based Technology which sets it apart from most of the competition. Most EFI controllers use what is called 'Alpha-N' Tuning Technology. Alpha-N tuning is associated with just using Throttle Position (TPS) and RPM as the factors to make tuning adjustments. Load Based Technology differs by using Rate, TPS and RPM as the key factors for adjustment. Load Based tuning allows a user to tune their vehicle for every gear and for all riding conditions. Load can easily be explained by stating that riding up a hill puts more "load" on the vehicle than driving on a flat road, but yet the same TPS and RPM can be achieved in both circumstances.

  • Offers Full Range Tunability
    The controller is sold as an Electronic Jet Kit. Like carburetor jet kits of the past the controller offers a range of adjustability to tune your vehicle. Instead of physical jets and needles the controller has this adjustability built into the unit and can quickly be adjusted while riding the vehicle. Essentially with all EFI vehicles software has replaced some hardware. The controller can be installed and set to actually allow the user to still run a stock configuration, but allows the user to ADD or PULL fuel within easy to understand tuning zones.

  • Does Not Interfere with Stock ECU Operation
    This is a very common feature of all after market EFI controllers, but needs to be stated to reassure all end users. The controller does not trip any engine codes or affect the ECU operation in any way.

  • Simple Push Button Adjustment Interface
    The controller offers 'on-the-fly' adjustment using three push buttons on the label interface. The three buttons are labeled MODE, PLUS, and MINUS. With power supplied to the box by either starting the vehicle or just turning the key on, the adjustment modes are accessed by pressing the MODE button. Light setting changes are then made for each respective mode by pressing the PLUS and MINUS buttons. No extra tools are required to make tuning adjustments.

  • Water-Resistant
    The hardware components within the controller are covered with a substance to make the controller water-resistant. The controller is still an electrical device and without this coating would short-circuit when in contact with water based substances. The controller is NOT 100% water proof, but will continue to function properly through rainstorms, snow, washing your vehicle, etc. Watch this YouTube video

  • 2-Year Warranty
    The controllers come with a two (2) year warranty from date of purchase against original defects in materials and workmanship. Should the controller fail to perform then the manufacturer will repair or replace the unit to the original retail purchaser at no charge except for shipping charges back to the manufacturer. Proof of purchase may be required.
    The controller does NOT void any OEM vehicle warranty. A common mispractice of dealers is to tell customers certain products will void their newer vehicle's warranty. The Magnuson-Moss Warranty Act protects consumers from this practice.


  • Item #: EJK-UTV
  • Manufacturer: Dobeck Performance

Dobeck Gen 3 / 3.5 UTV Fuel Programmers

Price: $225.00
* Marked fields are required.
Qty: *
Reviews (0) Write a Review
No Reviews. Write a Review